Response Electronics CL6011B Especificaciones Pagina 108
- Pagina / 170
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-30 Controller Cards
UM4.6:CS6003 Original — December 1991
Step 6: Connect the voltmeter between the heatsink (cathode) of
diode CR3 and the common (COM) test jack on the front of
the controller power conversion card. The voltmeter should
read 4.85
± 0.015 volts dc. If not, adjust the 5 VOLT (R53)
potentiometer on the controller power conversion card to
obtain the proper reading.
Step 7: Adjust the LOGIC RESET (R47) potentiometer on the
controller power conversion card until the RESET TEST
indicator on the calibrator lights and then back off the
potentiometer until the indicator just goes out.
Note
The ON indicator on the controller power
conversion card and the RELAY TEST indicator
on the calibrator should follow the RESET TEST
indicator during these steps.
Step 8: Adjust the 5 VOLT (R53) potentiometer on the controller
power conversion card until the voltmeter reads between 4.99
and 5.10 volts dc. The RESET TEST indicator should light. If
not, the controller power conversion card requires repair.
Step 9: Adjust the 5 VOLT (R53) potentiometer on the controller
power conversion card until the RESET TEST indicator just
goes out. The voltmeter should read 4.850
± 0.015 volts dc. If
not, repeat Steps 6 thru 9 until the proper reading is obtained.
Step 10: Adjust the 5 VOLT (R53) potentiometer on the controller
power conversion card until the voltmeter reads 5.180
± 0.005
volts dc.
Step 11: Connect the voltmeter between pin 41 (fifth pin from the
bottom on the component side of the card) on the backedge
connector of the controller power conversion card and the
common (COM) test jack on the front of the controller power
conversion card. The voltmeter should read –28.00
± 0.05
volts dc. If not, adjust the –28 VOLT (R29) potentiometer on
the controller power conversion card to obtain the proper
reading.
Step 12: Disconnect the voltmeter and jumper. The ON indicator on the
controller power conversion card and the RESET TEST and
RELAY TEST indicators on the calibrator should be lit. If not,
the controller power conversion card requires repair.
The output voltage levels are now calibrated. The remaining
steps set the alarm trip points.
5
- Using and Maintaining the 1
- Type CS6003 Calibrator 1
- Documentation Map 3
- Appendixes 8
- Contents 10
- Original — December 1991 10
- UM4.6:CS6003 10
- Section Tab Guide 11
- 1 Introduction 13
- 1.5 Related Documents 14
- 1.6 Manual Conventions 15
- 1-4 Introduction 16
- 2 Using the Calibrator 17
- 2.2.1 Cables 18
- 2.2.2 Front Panel 18
- Using the Calibrator 19
- 2.2.2.7 Breakout Terminals 20
- 2.2.2.11 Numerical Display 20
- 2.2.2.12 Family Switches 21
- 2.2.2.13 Group Mode Switches 21
- 2.2.2.14 CHK MOM Switch 21
- 2.2.2.15 CARD IDENT Switch 21
- 2.2.2.16 Mode Switches 21
- 2.2.2.17 Status Indicator 22
- 2.2.2.18 Data Switches 22
- 2.3 Operating the Calibrator 23
- 2.3.4.1 Lamp Test 24
- 2.3.4.2 Procedures 24
- ± 0.1% ± 1 count 25
- ± 0.002 Vdc 25
- ± 0.0005 mV 25
- ± 0.005 ohms 26
- ± 0.01 ohms 26
- 3 Card Removal, Cleaning, and 27
- Installation 27
- 3.3 Circuit Card Cleaning 28
- 3.4 Corrosion 29
- 4 Input and Output Card 31
- 4.1.1.2 Equipment Required 32
- 4.1.1.3 Calibration Procedure 32
- Input and Output Card 33
- (Isolated) 34
- X00606–A 35
- 4.1.3.1 Overview 39
- 4-10 Input and Output Card 40
- Figure 4-3. RTD Input Card 40
- R2, and R3 for the RTD card 40
- 4.1.3.2 Equipment Required 41
- 4.1.3.3 Calibration Procedure 41
- 1. Zero adjustment 43
- 2. Span adjustment 43
- 4.1.4.1 Overview 44
- 4-15Input and Output Cards 45
- 4.1.4.2 Equipment Required 46
- 4.1.4.3 Calibration Procedure 46
- Input Cards 48
- 4.1.5.1 Overview 49
- 4.1.5.2 Equipment Required 49
- 4.1.5.3 Calibration Procedure 50
- 4.1.6.1 Overview 50
- 4.1.6.2 Equipment Required 51
- 4.1.7.1 Overview 54
- 4.1.7.2 Equipment Required 54
- 4.1.7.3 Calibration Procedure 54
- Input and Output Cards 56
- X00613–A 57
- 4.1.8.2 Overview 60
- 4.1.8.3 Equipment Required 60
- 4.1.8.4 Calibration Procedure 60
- Current Output Cards 61
- 4.2.1.2 Equipment Required 62
- 4.2.1.3 Calibration Procedure 62
- 1. 0=OFF; 1=ON 64
- X00616–A 65
- REMOVE W1 FOR 65
- MOMENTARY OPTION 65
- 4.2.3.2 External Relay Panel 74
- 4.2.3.3 Switch Settings 74
- 4.2.3.4 Overview 74
- 4.2.3.5 Equipment Required 74
- 4.2.3.6 Calibration Procedure 75
- 4-48 Input and Output Cards 78
- 5 Controller Cards 79
- 5.1.1 MPU Card 80
- 5.1.2 Process I/O Card 83
- 5.2.1 MPU Card 85
- 5.2.1.2 Calibration Procedure 86
- 5.2.2 Process I/O Card 88
- 5.2.2.2 Calibration Procedure 89
- 5.3.1 Equipment Required 92
- 5.3.2 Calibration Procedure 92
- 5.4.1 Equipment Required 94
- 5.4.2 Calibration Procedure 95
- 5.5.1 Equipment Required 97
- 5.5.2 Calibration Procedure 97
- (with Dual Current Output) 99
- 5.6.2 Calibration Procedure 100
- ± 0.01 volts dc 101
- ± 0.02 volts dc. If not, the 101
- Manual Control Cards 102
- 5.7.2 Calibration Procedure 103
- 5.8.1 Equipment Required 104
- Conversion Card 105
- 5.9.2 Calibration Procedure 106
- Controller Cards 107
- ± 0.015 volts dc. If 108
- 5.10.1 Equipment Required 110
- 5.10.2 Calibration Procedure 110
- 5.10.3 Functional Test 111
- ± 0.08 volts 112
- 5.11.1 Equipment Required 114
- 5.11.2 Calibration Procedure 114
- 6 Data Highway Cards 115
- 6.1.2 Calibration Procedure 116
- ± 0.050 volts 117
- ± 0.002 volts dc 117
- ± 0.005 volts dc. If not 117
- Devices)(PN41B0985) 118
- 6.2.2 Calibration Procedure 119
- ± 0.010 volts 120
- ± 0.050 volts dc on the 120
- Appendix A 121
- Maintaining the Calibrator 121
- A.3 Lamp Test 122
- A.4 Fan and Filter 122
- Glossary 123
- DM6461, DM6462, DM6463, Using 159
- Document by Number 159
- UM4.6:CS6003, 1-1 159
- Reader’s Evaluation 167
- 1712 CENTRE CREEK DR 168
- AUSTIN TX 78754–9971 168
© 2020, manymanuals.es. Todos los derechos reservados | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales